IP Supervisor (AOR-IP-SUP) Installation
It is recommended that any load (device to be controlled) not be connected to the X12S module until after the X-600M has been configured and tested. By doing this, wiring and configuration mistakes will not cause the load device to turn on unexpectedly.
It is recommended that any load (device to be controlled) not be connected to the X12S module until after the X-600M has been configured and tested. By doing this, wiring and configuration mistakes will not cause the load device to turn on unexpectedly.
Cabling
Power
The AOR-IP-SUP includes a 24vdc 0.5A wall plug power adapter that will need to be connected to a 120v power supply, backup power may be required as per local codes.
On the X600M TM , the black/white wire connects to V+ and the black wire connects to V- .
Communication
A single CAT5e, or better will be needed to provide communications for the AOR-IP-SUP . This will connect to the ENET 1 .
The included Expansion cable is used to connect the X600M TM with the X12S TM , via the Expansion ports.
There are eight normally open relays on the X12S TM , that will accept 30AWG-14AWG wire, that is rated for at least 75°C.
| 14-Pin Connector Pinout |
|
|---|---|
| Terminal |
Description |
| 1NO |
Relay 1 NO
|
|
2NO
|
Relay 2 NO
|
|
3NO
|
Relay 3 NO
|
|
4NO
|
Relay 4 NO
|
|
1-4COM
|
Relay 1,2,3,4 COM
|
|
1-4COM
|
Relay 1,2,3,4 COM
|
|
1-4COM
|
Relay 1,2,3,4 COM
|
|
5NO
|
Relay 5 NO |
|
6NO
|
Relay 6 NO
|
|
7NO
|
Relay 7 NO |
|
8NO
|
Relay 8 NO
|
|
5-8COM
|
Relay 5,6,7,8 COM
|
|
5-8COM
|
Relay 5,6,7,8 COM
|
|
5-8COM
|
Relay 5,6,7,8 COM
|
Preparing the Enclosure
To prepare the mounting enclosure, a hole must be drilled to allow the cables to pass through, and the mounting tabs must be installed per the instructions included.
- Remove the mounting panel by removing the four(4) 9/16" nuts at the corners of the panel.
- Drill a hole large enough for an RJ-45 Ethernet connector, and the power cord to pass through.
- Following the instructions that were included by the manufacturer, attach the four (4) Mounting tabs.
Mounting the Enclosure
Mount the enclosure to the wall using fasteners and anchors appropriate for the construction of the wall.
Finish the installation by connection the Ethernet cable and power cable as outlined in the Cabling section above.
Related Articles
AOR-IP Supervisor Configuration
The AOR-IP-SUP comes pre-configured, for standard subnet used in the AOR-IP-SUP, but will need the proper configuration loaded and the scripts modified for the number of stations, in order to monitor the correct Network Devices. Configuration ...AOR-IP Command Unit Installation
This document covers the physical installation of the following AOR-IP Command Unit models: AOR-IP-40-CU AOR-IP-80-CU AOR-IP-120-CU AOR-IP-160-CU Fasteners The AOR-IP Command units can be surface mounted or flush mounted, as the particular ...AOR-IP Series Master Document
This document contains the links to other relevant documentation for the installation and configuration of the various components of the AOR-IP series AOR-IP Command Units (AOR-IP-40-CU, AOR-IP-80-CU, AOR-IP-120-CU, AOR-IP-160-CU) Installation AOR-IP ...AOR-IP Auxiliary Command Unit (ACU) Installation
This document covers the physical installation of the following AOR-IP Auxiliary Command Unit models: AOR-IP-40-ACU AOR-IP-80-ACU AOR-IP-120-ACU AOR-IP-160-ACU Fasteners The AOR-IP Command units can be surface mounted or flush mounted, as the ...AOR-IP Series Recommended IP Address Scheme
This article provides the recommended default IP addressing scheme for use with AOR-IP Series devices. The default IP address of the AOR-IP-CSE Series Call Stations is 192.168.1.10. This overlaps with with Extension 1010 in order to have enough ...