Talkaphone | Analog Call Stations

Analog Call Stations
How to change the Primary phone number on an ETP-400, ETP-500, ETP-100, ETP-103, or ETP-110
You will need to know the number associated with the telephone line that the Talkaphone is connected to, and the number that the Talkaphone should call when the button is pressed. This also assume that there is not another device on the line that is ...
Unable to answer incoming calls on the AVM-1 (GXV3370), or AVM-2 (GXV3350)
DND (do Not disturb) on GXV3370, GXv3350, AVM-1, AVM-2 IP-AOR-CU DND can also be enabled/disabled using the mute button (Mic icon) to right of keypad. You can disable this functionality by making the change below: - Web interface > Phone Settings > ...
ETP-500E not hanging up on Grandstream HT-814, HT-818, and HT-812
The HT-814, does not have the Loop Current disconnect signaling, that the ETP-500 will recognize, enabled by default. This will need to be enabled and the Loop Current Disconnect duration set to 700 ms.
ETP-400, ETP-500, ETP-100, ETP-110, Microphone not working on outbound call on autodial, ringdown, hotline or PLAR
For the ETP-520see this article, ETP-520 Programming Example for Autodial/Ringdown/PLAR Lines PLAR is another name for the ringdown/Autodial/Hotline Configure as follows Call into the station Dial *4** to access programming and, wait for a single ...
When attampting to program an ETP-100, ETP-100, ETP-400 or ETP-500 series device I receive 1 confirmation beep after the first * is entered.
This is a side affect of having two way conversation enabled on an inbound call (previously programming *78* into the device). After the response tone enter *4**, and you should receive the single confirmation tone. Proceed with programming as normal

Popular Articles
Programming the AOR series, and Analog stations for Day/Night Mode
Programming for an EC-8 or AOR Call into the unit or go off hook on the local phone, be sure and select the correct bank if working with an AOR-16, AOR-14, or AOR-32, and what for three tones. Enter *31** to access programming, wait for a single ...
BASIC Programming of Analog (ETP) Call Stations
What is the BASIC programming codes for the analog (ETP) devices? Resolution: What you will need: Analog telephone or test-set to dial in access to the ETP device The BASIC of QUICK programming for analog ETP devices is as follows: Default ...
What is the SIM Card Size for ETP-GSM (AT&T)
What type of SIM card does the ETP-GSM use for AT&T? ETP-GSM Answer: ETP-GSM uses the STANDARD SIM Card. SIM Card Sizes If you need additional assistance, please email us at support@talkaphone.com or call 773-539-1100 and select Technical Support.
Front status (CALLING and ANSWERED) LED's on VOIP Call Station Flashing
If the front LED's are continuously flashing on a VOIP-500/600 it means the device cannot register to a SIP server, firmware upgrade is in progress OR the device is in a constant reboot cycle due to not being able to obtain a DHCP IP address. ...
ETP-EL Blue Light flashes when not in a call
Issue: ETP-EL Blue Light flashes when not in a call Environment: ETP Towers that have a Blue Light on/in them. Resolution: Disconnect the ORANGE/BLACK from the call station, if flashing stops, possible issue with the call station. If the flashing ...

Talkaphone | Analog Call Stations | Knowledge Base

Analog Call Stations

How to change the Primary phone number on an ETP-400, ETP-500, ETP-100, ETP-103, or ETP-110

Unable to answer incoming calls on the AVM-1 (GXV3370), or AVM-2 (GXV3350)

ETP-500E not hanging up on Grandstream HT-814, HT-818, and HT-812

ETP-400, ETP-500, ETP-100, ETP-110, Microphone not working on outbound call on autodial, ringdown, hotline or PLAR

When attampting to program an ETP-100, ETP-100, ETP-400 or ETP-500 series device I receive 1 confirmation beep after the first * is entered.

Popular Articles

Programming the AOR series, and Analog stations for Day/Night Mode

BASIC Programming of Analog (ETP) Call Stations

What is the SIM Card Size for ETP-GSM (AT&T)

Front status (CALLING and ANSWERED) LED's on VOIP Call Station Flashing

ETP-EL Blue Light flashes when not in a call