VOIP-220/VOIP-221 Series
Configuring the AVM-1 (GXV3275) to link the video stream of an Axis Camera to the inbound Caller ID
Purpose This document address the basic configuration of an Axis camera to have a video stream that is compatible with the AVM-1. The screenshots in this document were taken from the M1025, but most Axis cameras have a similar interface. Login ...
Programming the AOR series, and Analog stations for Day/Night Mode
Programming for an EC-8 or AOR Call into the unit or go off hook on the local phone, be sure and select the correct bank if working with an AOR-16, AOR-14, or AOR-32, and what for three tones. Enter *31** to access programming, wait for a single ...
How To Install the AVM-1 (GXV3275) and the VOIP-500 or VOIP-600 (with IP Camera) - Peer To Peer
This knowledge article describes the setup of the AVM-1 and the VOIP-500 or VOIP-600 (With IP Camera) in a peer-to-peer environment: Assumptions: Technician has fundamental knowledge in computer networking and Voice over Internet Protocol (VoIP) ...
Set VOIP-200 Series To Ring Until Answered.
Set Buttons(Idle), Button 1, Option to Numberlist 1 Enter the number to be called as Value 1 of Ringlist 1 Mark the Checkbox for Call Until Answer Set the Ringer Time to a higher number to allow enough rings between each call attempt, 60 seconds to ...
Run a Digital Output script from a call originated from an AVM-1 to the VOIP-200/VOIP-500/VOIP-600 IP Call Stations
To call into the VOIP-200/VOIP-500/VOIP-600 IP Call Stations from the AVM-1, select IP Call from the drop-down. Then put in the IP address of the IP Call Station(use * for a dot on the soft keypad on the AVM-1). The IP Call Station will auto-answer ...
How To Install the AVM-1 and the VOIP-20X (with IP Camera) - Peer To Peer
This knowledge article describes the setup of the AVM-1 and the VOIP-20X (With IP Camera) in a peer-to-peer environment: Assumptions: Technician has fundamental knowledge in computer networking and Voice over Internet Protocol (VoIP) technologies is ...
BASIC Programming of Analog (ETP) Call Stations
What is the BASIC programming codes for the analog (ETP) devices? Resolution: What you will need: Analog telephone or test-set to dial in access to the ETP device The BASIC of QUICK programming for analog ETP devices is as follows: Default ...
Popular Articles
Programming the AOR series, and Analog stations for Day/Night Mode
Programming for an EC-8 or AOR Call into the unit or go off hook on the local phone, be sure and select the correct bank if working with an AOR-16, AOR-14, or AOR-32, and what for three tones. Enter *31** to access programming, wait for a single ...
BASIC Programming of Analog (ETP) Call Stations
What is the BASIC programming codes for the analog (ETP) devices? Resolution: What you will need: Analog telephone or test-set to dial in access to the ETP device The BASIC of QUICK programming for analog ETP devices is as follows: Default ...
What is the SIM Card Size for ETP-GSM (AT&T)
What type of SIM card does the ETP-GSM use for AT&T? ETP-GSM Answer: ETP-GSM uses the STANDARD SIM Card. SIM Card Sizes If you need additional assistance, please email us at support@talkaphone.com or call 773-539-1100 and select Technical Support.
Front status (CALLING and ANSWERED) LED's on VOIP Call Station Flashing
If the front LED's are continuously flashing on a VOIP-500/600 it means the device cannot register to a SIP server, firmware upgrade is in progress OR the device is in a constant reboot cycle due to not being able to obtain a DHCP IP address. ...
ETP-EL Blue Light flashes when not in a call
Issue: ETP-EL Blue Light flashes when not in a call Environment: ETP Towers that have a Blue Light on/in them. Resolution: Disconnect the ORANGE/BLACK from the call station, if flashing stops, possible issue with the call station. If the flashing ...